Sun Solaris 10 Download X86 Dvd Iso Burner

Sun Fire X2250 Server Operating System Installation GuideC H A P T E R 2Solaris InstallationThis chapter contains instructions for installing the Solaris 10 Operating System from network or media, and is intended for experienced system administrators who are familiar with using the Solaris OS on an x86 platform.Note - If you are configuring the preinstalled Solaris 10 Operating System that is shipped with the server, refer to the Sun Fire X2250 Server Installation Guide.This chapter contains the following topics:. Installation RequirementsBefore starting the Solaris 10 installation, you should ensure the following requirements are met. Proper format of Solaris 10 distribution files. Depending on the installation method chosen to install Solaris, you will need to have either the Solaris Distribution CD/DVD, ISO image, or JumpStart image readily available for installation. Minimum supported Solaris OS. The X2250 server supports the following minimum Solaris Operating System:.

1. Solaris 10 5 09 Iso Download

Solaris 10 5/08 or laterYou can download or order the media for Solaris 10 at. Established console access to installation. You should have already chosen a supported console option to display the input or output for the installation.

For more information, see. Properly configured boot device in BIOS. Checklist of Tasks to PerformThe following tasks must be performed in the order in which they are listed.

Note that not all tasks are mandatory.TABLE 2-1 Checklist for Solaris InstallationsStepsMandatory or OptionalTask1MandatoryEstablished installation environment. For more information see:.2OptionalSet optimal default settings in the BIOS Setup Utility. For more information, see.3MandatoryLocate the Sun Fire X2250 Tools and Drivers CD provided with the X2250 server or download the required system device drivers from the following site:4MandatoryBoot the Solaris 10 installation program to initiate the operating system installation. For more information see:.5MandatoryInstall the system device drivers required for Solaris 10 installation.

For more information, see. Install Solaris 10 Using JumpStart Network InstallationThis section summarizes the steps for installing the Solaris 10 OS over the network using a JumpStart image.For additional information about performing a network installation, go to. For specific information about performing custom JumpStart network installations, go toNote that the installation server must have a CD/DVD drive, and it must be part of the site’s network and name service. If you use a name service, the server must already be in a name service, such as NIS, NIS+, DNS, or LDAP. If you do not use a name service, you must distribute information about this server by following your site’s policies.To Install Using JumpStart Network Installation1.On the system that is to become the installation server, log in as root (superuser).2.Insert the Solaris 10 media into the server's CD/DVD drive.3.Open a terminal window.Enter the commands in this procedure in the terminal window at the system prompt.4.Create a directory for the CD image.

Type:# mkdir -p installdirpathinstalldirpath represents the directory where the CD image is to be copied.5.Change to the Tools directory on the mounted disc. Type:# cd /cdrom/cdrom0/Solaris10/Tools6.Copy the image in the drive to the installation server's hard drive.

Solaris 10 5 09 Iso Download

Type:#./setupinstallserver installdirpathinstalldirpath represents the directory where the CD image is to be copied.Note - Executing the setupinstallserver command shows whether you have enough disk space available for the Solaris 10 Software disc images. To determine available disk space, use the df -kl command.7.Change directories to root ( /). Enter:# cd /8.Eject the Solaris 10 media.9.Proceed with the instructions provided in:.or. Install Solaris 10 From Local or Remote Distribution MediaThe following procedure describes the initial steps involved for booting the Solaris 10 installation media from local or remote media (CD/DVD distribution media, ISO CD image, or JumpStart image). Use this procedure, along with the instructions for x86 platforms in Solaris 10 5/08 Installation Guide: Basic Installations (820-4040), to install the Solaris OS onto a X2250 server.Note that the installation method described in this procedure includes directing the server output to the local console or to the Sun ILOM Remote Console when a local or remote CD/DVD drive is used.

For additional information about redirecting storage devices in the Sun ILOM Remote Console, see.Prerequisite. Reviewed and met the requirements listed inTo Install Solaris From Local or Remote Distribution Media1.Do one of the following:. For distribution CD/DVD. Insert the Solaris 10 Distribution media (CD labeled #1 or the single DVD) into the local CD/DVD drive. For ISO CD image or JumpStart image.

Install Solaris 10 Using a Serial Terminal Follow this procedure if you want to display the installation output to a serial terminal. The steps provided in this procedure only apply to the installation output. Prerequisites:. A serial terminal. The serial terminal can be a VT100, a PC running terminal emulation, or a terminal server. Configured serial terminal properties.

The serial properties on the attached console should match the following default serial port settings:. 9600 baud. 8N1 (eight data bits, no parity, one stop bit).

Disable flow control. The system that you use as an installation server must include a CD/DVD drive and be part of the network and name service. Install System Device Drivers (Post Solaris Installation)After installing the Solaris 10 software on the X2250 server, you should install the AST2000 VGA driver.Prerequisites. Sun Fire X2250 Server Tools and Driver CD or the Sun Fire X2250 Tools and Driver CD ISO image.Note - The Sun Fire X2250 Server Tools and Drivers CD is provided in the Documentation and Media Kit, which is a customer orderable option.

If necessary, you can also download an ISO image of the Tools and Drivers CD at. Established installation environment. For more information, see and.Note - This installation method includes directing the server output to the local console or to the Sun ILOM Remote Console when a local or remote CD/DVD drive is used. For more information about redirecting devices to the Sun ILOM Remote Console, see.To Install System Device Driver From Local or Remote Media1.Do one of the following:.

For distribution CD/DVD. Insert the X2250 Tools and Driver CD into the local or remote CD/DVD drive.

For customer-provided ISO image. In the Device menu of the Sun ILOM Remote Console, select CD-ROM image to specify the location of the customer-provided ISO image.2.Change to the /cdrom/cdrom0/drivers/sx86 directory by typing the following command:# cd /cdrom/cdrom0/drivers/sx863.Run the install script by typing the following command:# sh install.shThe system device driver(s) are now installed. The script prompts you to reboot the system for changes to take effect.4.Reboot the X2250 server.

As an adjunct to the, a slightly customized boot environment capable of enabling serial console kernel debugging was required to diagnose Solaris install problems. The post itself mentioned that a nice way to accomplish this was to set up PXE network boot via. It is indeed flexible and enables one to experiment with modifications and quickly test whether they perform as expected. The one downside to this environment is that an additional DHCP/TFTP boot server has to be configured. To eliminate that service, you could, once the customizations are well understood, simply create a new version of the Solaris install DVD with your customizations. Let's run through the process for a simple example.1. Get a Solaris DVD.

For this example, we'll use an interim build of the upcoming Solaris 10 Update 5.2. Extract the the entire contents of the DVD. # lofiadm -a /export/iso/s10xu5b10dvd.iso/dev/lofi/1# mkdir -p /iso# mount -r -F hsfs /dev/lofi/1 /iso# cd /iso# mkdir /export/modified-s10xu5b10# find.depth -print cpio -pudm /export/modified-s10xu5b104516208 blocks3. Modify the content contained in /export/modified-s10xu5b10.

In this case, we'll change the boot/grub/menu.lst file found in this directory to look like: ##pragma ident '@(#)installmenu 1.1 05/09/01 SMI'#default=0timeout=30serial -unit=0 -speed=9600terminal serialtitle Solaris Serial Console ttyakernel /boot/multiboot kernel/unix -B installmedia=cdrom,console=ttyamodule /boot/x86.miniroot4. Issue the following magic incantation to create a bootable ISO image based on the contents of the /export/modified-s10xu5b10 directory.